|
SANGER CYCLES-1724 East Lincoln Avenue, Suite B1, Fort Collins, CO 80524, 970-419-5500
88-95 CUBIC INCH KITS TC 96-103 CUBIC INCH KITS TC
EFI WILD KIT $3870.00/PARTS & LABOR CARB MODEL KIT $3240.00
Wiseco Piston Kit $410.95 Labor $600.00 570G Cam 325.95 Boring 180.00 Gear Drive Set 439.95 Heavy Bearing Kit 36.95 10 Litre Heads 980.95 Adjustable Pushrods 169.95 Gasket Kit 60.00 Power Commander 369.95 Custom Map/Tune (EFI only) 225.00 (after 500 mile break in)
EFI MILD KIT $2860.00/PARTS & LABOR CARB MILD KIT $2250.00
Wiseco Piston Kit $410.95 Labor $600.00 510G Cam 325.95 Boring 180.00 Gear Drive Set 436.95 Heavy Bearing Kit 36.95 Pushrod Set 169.95 Gasket Kit 60.00 Power Commander 369.95 Custom Map/Tune (EFI only) 225.00 (after 500 mile break in)
Recommend the Power Commander /Custom Map/Tune/Air Filter Kit/Exhaust System on the EFI models. (If over 20,000 miles a valve job should be done, over 50,000 miles crank work should be done.)
GEAR DRIVE CONVERSION KIT $1230.00/PARTS & LABOR S&S 510G Set w/Cams & Bearings $720.95 Labor $300.00 Pushrod Set 169.95 Gasket Kit 40.00 This is a mild cam which gives you good low end & mid range torque. Larger lift cams such as the 570G are used with head work.
80 CUBIC INCH KITS EFI EVO WILD $3300.00 PARTS & LABOR CARB MODELS $3100. Piston Kit $188.00 Cam Bearing Kit 10.00 581 Cam 215.00 Jim’s Big Axle Lifters 344.00 Mikuni Smooth Bore 384.00 10 Litre Heads 980.00 (Carb models only) Gasket Kit 86.00 Adjustable Pushrod Set 169.95 Custom Map/Tune 225.00 Power Commander 369.95 CylinderBoring 90.00 Labor 600.00
EFI EVO MILD $2350.00 PARTS & LABOR CARB MODELS $1775.
Piston Kit 188.00 Power Commander 369.95 500 Cam 215.00 Custom Map/Tune 225.00 Cam Bearing Kit 10.00 Labor 600.00 Jim’s Lifters 395.00 Cylinder Boring 90.00 Gasket Kit 86.00 Adjustable Pushrods 169.95 Recommend Zipper Air Filter/2-1 Exhaust, update to Mikuni HSR 42mm. Power Commander & Custom Map (EFI models)
LABOR PRICES Engine Hop-Up $600.00 Big Bore Cylinder Boring $180.00 3 Angle Valve Job 280.00 Cylinder Boring 90.00 Crank Job 995.00 10 Litre Heads require exchange w/good heads
CARB CONVERSION KIT $1390.00 PARTS & LABOR 1996-2001 FL models w/M&M EFI recommended for these bikes.
103 – 116 – 124 CUBIC INCH KITS COMPLETE ENGINE & BIG CUBIC INCH KITS-Prices range from $4800.00-7400.00 Depending on cubic inch & finish LABOR PRICES Install Big Inch Kits $900.00 Engine Case Boring 295.00 110 CUBIC INCH EVOLUTION ENGINE REPLACMENT WITH REV TECH ENGINE. There may be additional parts needed to complete replacement if other parts are worn out. Prices are not included with the labor charge. LABOR PRICES Install New Engine $500.00
SIX SPEED INSTALL $1984.99 PARTS & LABOR 6 Speed Insert Kit $1290.00 Speedometer Recalibration $139.99 Gaskets & Oil 75.00 We recommend installation of Oil Coolers & Adapters to help keep the motor cooler. The 2 into 1 Exhaust System or True Duals also give the bike more horse power and torque, along with K&N zipper type air filter.
After the first 500 mile break in we recommend that you switch to Redline Synthetic Motor oil 20W60.
Again these are estimated prices only. If there are other parts that need to be replaced on the bike in order for the job to be completed there will be additional charges. We strive for the best work to be done and we will not send a bike out of the shop unsafe for the customer. Unless the customer requests the job be unfinished. We will not be responsible for irresponsible riders.
|